Comet MS6 datalogger med 16 kanaler

Total memory capacity:

2MB (up to 480 000 values)

Memory type:

internal backed-up SRAM memory

Data logging modes:

Stop-when-full or cyclic

Data logging intervals:

adjustable individually for all input channels from 1 second to 24 hours

Real time clock:

year, leap year, month, day, hour, minute, second, backed-up by Lithium battery

Input signals:

16 user configurable channels - see parameters in the table below

AD converter (analog channels):

16 bits, conversion duration approximately 60ms/channel

Supported interface for communication with computer:

every 10 s

Included interfaces: RS232 and USB
Optional interfaces:
GSM - With GSM modem connected to RS232 interface. Enables GPRS and SMS comm.
RS485 - Enable connection of several data loggers to one line, cable lenght up to 1200 m, galvanically isolated.
Ethernet - SNMP, SOAP, www-pages

Communication speed:

9600, 19200, 57600, 115200 Bd

Outputs for alarm indication:

Red LED at the side of the case, 32 LEDs
Relay max. 8A/250Vac, switching-over contact
Voltage signal 0V/4.8V, max current 50mA.
Alarm SMS messages
E-mails, SNMP traps - see optional accessory

Power:

24V DC, consumption of data logger itself approximately 80 mA

Operating temperature range:

0 to +50°C

Dimensions with plugged connectors:

215 x 225 x 44 mm (W x H x D)

MEASURED VALUE

ACCURACY

NOTE

DC current 4 to 20 mA
DC voltage -10V to +10V

±0.1% FS (±0.02 mA)

either from active source connected to COM and GND terminals or passive sensor across terminals +24V and COM

DC voltage -1V to +1V

±0.1% FS (±10 mV)

input resistance appr. 10 MOhms, input terminals IN and COM

DC voltage -100mV to +100mV

±0.1% FS (±1 mV)

input resistance appr. 10 MOhms, input terminals IN and COM

DC voltage -18mV to +18mV

±0.1% FS (±100 uV)

input resistance appr. 10 MOhms, input terminals IN and COM

Thermocouple K (NiCr-Ni)

±0.1% FS (±18 uV)

input resistance appr. 10 MOhms, input terminals IN and COM

-200 to +1300°C
Thermocouple J (Fe-Co)

±0.3% from reading + 1.5°C

linearized, cold junction compensation, input terminals IN and COM

-200 to +750°C
Thermocouple S (Pt10%Rh-Pt)

±0.3% from reading + 1.5°C

linearized, cold junction compensation, input terminals IN and COM

0 to +1700°C
Thermocouple B (Pt30%Rh-Pt)

±0.3% from reading + 1.5°C

linearized, cold junction compensation, input terminals IN and COM

+100 to +1800°C
Thermocouple T (Cu-CuNi)

±0.3% from reading + 1.0°C
from +300 to +1800°C

linearized, without cold junction compensation, input terminals IN and COM

-200 to +400°C Platinum RTD
sensor Pt100

±0.3% from reading + 1.5°C

linearized, cold junction compensation, input terminals IN and COM

-200 to +600°C
Platinum RTD sensor Pt1000

±0.2°C from -200 to +100°C
±0.2% from +100 to +600°C

two-wire connection, measuring current appr. 0.8mA in 50ms pulse, input terminals IN and COM

-200 to +600°C
Nickel RTD sensor Ni1000/

±0.2°C from -200 to +100°C
±0.2% from +100 to +600°C

two-wire connection, measuring current appr. 0.5mA in 50ms pulse, input terminals IN and COM

6180ppm -50 to +250°C
two-wire measuring of resistance

±0.2°C from -50 to +100°C
±0.2% from +100 to +250°C

two-wire connection, measuring current appr. 0.5mA in 50ms pulse, input terminals IN and COM

0 to 300 Ohms
two-wire measuring of resistance

0.1% FS (±0.3 Ohms)

two-wire connection, measuring current appr. 0.8mA in 50ms pulse, input terminals IN and COM

0 to 3000 Ohms
two-wire measuring of resistance

0.1% FS (±3 Ohms)

two-wire connection, measuring current appr. 0.5mA in 50ms pulse, input terminals IN and COM

0 to 10000 Ohms

0.1% FS (±10 Ohms)

two-wire connection, measuring current appr. 0.1mA in 50ms pulse, input terminals IN and COM

Binary input for two-state signal

Input voltage for state "L" (IN-COM) < 0.8 V (Rin < 1 kOhm).
resistance of closed contact for state "L" (IN-COM) < 1 kOhm.
input voltage for state "H" (IN-COM) > 2 V.
resistance of closed contact for state "H" (IN-COM) > 10 kOhm.
minimum duration for sensing of change: 200ms.

RS485IN
- input for serial signal RS485
- optionally

E.g. data acquisition from temperature, humidity, pressure sensors Tx41x, Hx43x.
Input serves for reading from devices supporting protocol ModBus RTU or Advantech.
Connected to terminals next to terminals for channel 15 and 16.
Input can work with 16 devices. Maximum speed 115200Bd. Galvanically isolated.

MS Logger Program

Free MS Logger Program

SWR006 MS Logger Program

DBM MS Logger Program

Data download from data logger:

yes

yes

yes

Opening of record from file:

yes

yes

yes

Data export to dbf and xls formats:

yes

yes

yes

Data view in table:

yes

yes

yes

Fully settable graph:

-

yes

yes

Export of graph to pdf format:

-

yes

yes

Print of data table:

yes

yes

yes

Print of graph:

-

yes

yes

Selection of values for print from table:

-

yes

yes

Event logging/event viewing:

yes

yes

yes

Data Logger Configuration:

yes

yes

yes

Data download with export to dbf format:

-

yes

yes

Erasing of data logger memory:

yes

yes

yes

Invalidation of logger audio alarm indication:

yes

yes

yes

Reading of data logger configuration from file:

yes

yes

yes

Statistics:

yes

yes

yes

Setting of folder and file for data storing:

-

yes

yes

Alarm warnings in online Display mode:

-

yes

yes

Program security - users and passwords:

-

yes

yes

Autodownload:

-

yes

yes

Data export to SQL database:

-

-

yes

Data download with export to SQL database:

-

-

yes

Autodownload with data export to SQL dbase:

-

-

yes

Viewing of data in SQL database:

-

-

yes